Sunday, March 30, 2014

The Precautions When You Handle The Intelligent Tester

When you using the intelligent tester and its accessories,please must remember and do follow the following points I will mention here.

If you update the software of your intelligent tester,all the setting parameters would change ,using the tool option function can be reset to their factory settings.If you want,you can go back and change the settings manually.
Don't let the intelligent tester or its accessories exposed under the direct sunlight for a long period of time, and try to avoid using it in high-temperature places.If you put it in low-temperature locations,the display response may be slow,but don't worry,it is caused by the characteristics of the LCD display,so it is a normal thing.Besides,don't use the tool in somewhere with high humidity,or the display back light would deteriorate and the brightness would be decreased,so remember to use and store the intelligent tester and its accessories in the place with low humidity.
After using the intelligent tester,if you wanna clean it and its accessories,don't use paint thinner or any other solvent or volatile oil product,or it could cause deformation,discoloration and some other problems such as loss of function.When you wipe it,please be gently with a soft cloth dipped in a diluted neutral detergent.
If you have a long time didn't use the intelligent tester,then the clock may be inaccurate or even stop working,then you need to reset the clock and it will be ok.And if the internal battery remains completely drained for a prolonged time,the service life of the battery would be shorten,so remember to charge the interal battery at least once a month even you are not going to use the tool.
If you wanna propose your intelligent tester and its accessories,please ask the waste processing company for help to handle the tool seperate to ordinary non-burnable material.Because the they contain electronic parts instakked using solder that includes lead,and the lead would damage the environment.
And you should also ask the company to propose the different plastics.The plastic case of it is made of polycarbonate,ABS and acrylic.except the clear panel,the plastic parts have materials abbreviations stamped inside and these compound plastic products can be recycled.
Besides,you need to dispose the used internal batteries follow the regulations of your nation and region.

Wednesday, March 26, 2014

AD900 Pro Key Programmer

The AD900 is an excellent professional key programmer,it can identify,read out and copy transponder,it can also write the transponder codes.Here let's know more details about this tool.
On the main menu diapaly,there are six options,they are "Identify","Write code","Copy","Special","Setup" and "Test".

First is the "Identify",it can determine all the things about the transponders that are used in automobile sector,such as transponder logics,transponder types and eeprom logics,the brands of vechiles.
The "Write code" function is used to write the fixed transponder codes.You can choose the transponder type that you want to write to,and then write down the codes and press the button of "Enter".
Then the section of "Copy" which is used to copy the transponder if there is a transponder can be copied.
The fourth section "Special" is also another menu.This menu includes the information that has never seen before and all these special features make this tool unique.The features in this menu can be improved while the immobilizer systems are developing.In this menu,there are "Random Code","Ren 33 pin","Hyundai Kia Pin","Eeprom" and "Unlock 48".
1.Random Code can produce codes for constant coded transponders and show the codes that you have to write to vehicles memory from the produced codes.
2.Ren 33 Pin will calculate pin-codes for the ID 33 Renault vehicle's transponders.This code can identify the vehicle to the second remote control by a diagnostic device and can determine if the vehicle belong to a transponder or not.
3.The system of "Hyundai Kia Pin" solved the problem of Hyundai and Kia.The pin code will be calculated when the last six number of chassis is entered to the system.
4.The "EEPROM" can help you produce the transponder that belongs to the vehicle.Even the vehicle has no key,it can also work.
5.The "Unlock 48"is used to unlock the 48 Megamos Crypto transponders which are locked when identified to a new generation vehicle.

The fifth is "SETUP".You can see the version and the serial number of the AD900 and you can select the language that you want while you use this tool.Besides,if it has a new version,you can update your AD900 in "SETUP".
The sixth and also the last one is "TEST".It is used to test the key that if there has a transponder or not.

Tuesday, March 25, 2014

Some Tips Of Using The Autel Maxidas DS708 To Do The Quickly Troubleshooting

The Autel Maxidas DS708 is an excellent vehicle diagnostic tool.Some users want to use this tool to perform the troubleshooting.So here I wanna share some tips of using DS708 to do the quick troubleshooting.

First,you need to check the external adapters,if there is an on/off switch,you should make sure that the adapter of your network router is turned "on" and also check the LED indicators to
ensure that the tool is functional.
The SSID and WEP key information that you have entered are case sensitive,so you should check with someone in the establishment to see whether the SSID has been changed or not if you had got the information of SSID from the internet.
Next,you need to restart your network router and check all the cables, connections and indicators to ensure the signal is being received and dispersed in an appropriate manner.
For connecting to wifi network successfully,you have to ensure that there has no signal interference,yet the Microwave ovens, cordless telephones and some medical or scientific instruments may interfere it,so try to move them away or do this procedure in a place where won't get the signal interference.Then you should select the right authentication type according to the router settings of your Wi-Fi local network.
You need to pay attention to your steps while you are performing the configuration,because one of the common reason of incorrect configuration is user's error.If you can remember and follow these,you must do the troubleshooting better.

Sunday, March 23, 2014

About The Software Of EasyDiag

EasyDiag is an intergrated service platform based on automotive diagnosis solution.It can achieve following functions:vehicle diagnosis, operational data query, automotive repairment, data and information sharing;which provide a wide range of automotive diagnostic community.

Users just need to use the Bluetooth connectors(DBScar connector) to communicate with their vehicles. The data between the terminal and connectors is transmitted via Bluetooth, it owns all the functions of full diagnostic, which includes full electronic control system trouble diagnosis, and it can read and clear Diagnosis trouble codes and read data stream.
Circle and the instant message can help users share their maintenance knowledge of vehicle easily, users can communicate their vehicle maintenance experience, ask their troubles of vehicle maintenance and also can get the vehicle maintenance service support online. It's the home of maintenance technicians, where you can have the information you want.
EasyDiag is an excellent auto diagnostic tool which get the perfect combination with the Internet, it is a revolution of the vehicle diagnostic tools. You can free download and install the EasyDiag app, experience the best trouble diagnostic app for smart vehicle of mobile-internet full of creative. If you need the latest vehicle trouble diagnostic technology, you can buy a portable EasyDiag diagnostic connector.With this connector,and connected with your smart phone or tablet PC, you can do the vehicle diagnosis and many other internet functions intergrated by the app product.

Wednesday, March 19, 2014

Cummins INLINE 5 INSITE 7.6 Data Link Adapter

Cummins INSITE 7.6 is a PC-based software application.It can easily access to users' engine's electronic performance information , which enables faster service turn around times. INSITE helps to ensure accurate procedures and diagnosis and limit downtime, while increasing productivity and profits.
Cummins INLINE 5 software provides the information of engine quickly, and users can get the inside details they need. No matter what kind of equipment you run, Cummins INSITE 7.6 can fit all Cummins electronic engine,no matter what equipment you run.

Cummins INSITE 7.6 supports multi-languages,such as English(UnitedStates),Chinese(Simplified),Danish,Dutch(Netherlands),Finnish,French(France),German(Germany),Italian(ltaly),Japanese,Korean,Norwegia(Bokmal),Portuguese(Brazil),Ruaaian,Spanish(Traditional Sort),Swedish and Turkish.

About the functions of the Cummins INSITE 7.6:
1.Trip and vehicle information
2.Parameter and feature adjustment
3.The accurate problem diagnosis
4.Complete wiring diagram sand sensor location maps
5.Step-by-step trouble-shooting information
6.Fault tree information
7.Fault code and symptom-based diagnostics
8.Engine diagnostic tests
9.Tools to create templates for a group of vehicles
10.Fleet management/driver reward programs
11.Audit trail information
12.Enhanced ECM security

The Cummins INSITE 7.6 is small enough to be put in your pocketm,the housing of it is made of aluminum so it can be protect well.It supports SAE J1708/J1587 and J1939/CAN data links,USB full speed port at up to 2M baud rate and RS-232 PC/PDA serial port at up to 115.2k baud rate.It is fully compliant with TMC's RP1210 standard.
The operating temperature of Cummins INSITE 7.6 is rated for -40° to +85° C.It needs 8 V to 50 V DC power from vehicle.It includes advanced processor for maximum speed and performance,it also has 5 LED to indicate power and USB, RS-232, J1708/J1587, and J1939/CAN communications.The internal flash memory of it allows firmware upgradeability.

Tuesday, March 18, 2014

Creator C300 Scan Tool

Creator C300 OBDII/EOBD Scan Tool is a hand-held diagnostic tool,which usually used to view freeze frame data,identify pending codes,read,graph and display live PCM data stream and read I/M Readiness Status,retrieve generic (P0, P2, P3, and U0) and manufacturer specific (P1, P3, and U1) codes.Creator C300 can turn off the Check Engine Light,clear codes,reset monitors and retrieve the information of vehicle(VIN,CIN and CVN),it supports CAN (Controller Area Network) and all the other current OBD-II protocols.Creator C300 can determine the cause of the Check Engine Light easily.

Creator C300 supports multi-language,such as English, Germany, Simplified Chinese, Traditional Chinese, Spanish and Vietnamese .It can work on all 2001 and later OBDII compliant PETROL European vehicles,all 2004 and later OBDII compliant DIESEL European vehicles,all 1996 and later OBDII compliant US and Asian vehicles.It supports J1850 PWM VPW, KWP2000, ISO9141, CAN diagnosis.And It is very convenience to update the Creator C300 software online via USB 2.0 for free.
Creator C300 can perform the modules present test and live O2 sensor test,and display the test data on unit screen ,also the DTC definitions will show on it.Besides,the communications data can be remained and re-display.

The Specifications of the Creator C300 OBDII/EOBD Scan Tool:

1. Display: 2.8" Color LCD, 320 * 240 pixel display with contrast adjustment
2. Operation Temperature: -20 ℃ -- 75 ℃
3. Storage Temperature: -40 ℃ -- 120 ℃
4. Power: 8V -- 18V
5. Dimensions: 135mm x 85mm x 26mm
6. Net Weight: 250 g ; Gross Weight: 450 g
7. Certification: CE, FCC, ROHS
8. Protocols covered:
SAE J1850 PWM (41.6 kbaud)
SAE J1850 VPW (10.4 kbaud)
ISO 9141-2 (5 baud init, 10.4 kbaud)
ISO 14230-4 KWP 2000 (5 baud init, 10.4 kbaud)
ISO 14230-4 KWP 2000 (fast init, 10.4 kbaud)
ISO 15765-4 CAN (11 bit ID, 500 kbaud)
ISO 15765-4 CAN (29 bit ID, 500 kbaud)
ISO 15765-4 CAN (11 bit ID, 250 kbaud)
ISO 15765-4 CAN (29 bit ID, 250 kbaud)

Monday, March 17, 2014

LAUNCH CNC-602A Injector Cleaner & Tester 110V

Launch CNC-602A is an advanced electro-mechanical tool, it can clean and test injectors by simulating engine's working conditions. It can also do the cleaning on the injectors and fuel supply system on vehicle.Attention,this product supports English and it has two kinds,one is 110V and another is 220V.

One of the functions of CNC-602A is Ultrasonic cleaning,it help the tool to perform simultaneous cleaning on several injectors and to remove the carbon deposits on the injector completely.The Uniformity/Spray ability test is to test the uniformity of injecting amount of each injector, and to monitor the spraying status of each injector with the help of backlight. This test is also for reverse flush.And the Leakage test is to test the sealing and dribbling conditions of injectors under system pressure.Then the Injecting flow test is to check the injecting amount of the injector in 15 seconds of constant injection.The last Auto test is to test injectors by simulating different working conditions.There is a unit called On-vehicle cleaning,which is equipped with various adaptors and couplers that facilitate cleaning on the injectors on vehicle.

The parameters of Launch CNC-602A:
Power supply: AC220V±10%, 50/60Hz; AC110V±10%, 50/60Hz.
Ultrasonic cleaner power: 100W;
Input power: 250W;
Simulated RPM range: 10~9990rpm; step: 10rpm;
Time range: 1~9999s;
Pulse width: 0.5~25ms; step 0.1 ms;
Fuel tank capacity: 4700ml;

The supported Car Makers:
Audi, Australia Ford, Benz, BMW, Brilliance, Chevrolet, Chevy, Chrysler, Citroen, Dacia, Dadi, Daewoo, Daihatsu, Demo, Fiat, Ford, GM, Holden, Honda, Hyundai, Isuzu, Jaguar, Kia, Lancia, LandRover, Mahindra, Maruti, Mazda, Mitsubish, Nissan, Opel, Peugeot, Porsche, Renault, Romeo, Rover, Saab, Seat, Skoda, Smart, Subaru, Suzuki, Tata, Toyota, Volvo, VW, Yamaha.

Sunday, March 16, 2014

How To Program Keys with Vagtacho USB 4.0

1.Switch ON ignition with any key no mater new or old.
Start software, choose "VDO NEW - CAN bus",and then press "Connect Selected ECU" button, after 5 seconds the data of the dash will show on screen.
Press "Program New Key", software will read data from the dash and after few seconds a new window will be opened.
See the picture below. ID numbers of the transponders which are stored into memory will be shown.
step 1
2.This is the TMPro module#146 window. Insert transponder key with new Megamos ID48 chip and program it.
3.Press "Add Key" and there will show a message. Switch ON ignition with key which you want to program! Vagtacho will check the key if the key is new or old.New means it's already programmed with TM Pro; Old means the key has been used with the same car. If this key is already programmed to the car or it is from another car, Vagtacho will show warning message on screen and won't program this key!
4.If everything is ok, Vagtacho will add the new key into the data of immobilizer and will show new key's ID number on screen. See the red mark on the picture. Now you can program the new transponder key into the immobilizer. Press "Write Keys" to finish the procedure .
5.Press "Write Keys" and the warning window will open. If you are sure that everything is all right, press"Continue", otherwise press "Cancel",then the data won't be written into immobiliser. After pressing "Continue",Vagtacho will write the data into immobiliser after few seconds. The dash will be reset, and the programming procedure will be completed.
This is the last step, after this the new data will be written into immobiliser! If you have marked and erased some keys, they won't work anymore!
6.This picture shows the final Vagtacho window. If you have switched ON ignition with key which is already programmed by TMPro, the warning lamp of immobiliser on the dash will be turned off. The new key is already stored into immobiliser and you can start engine.
7.If the warning lamp is still flashing, there is something wrong in the procedure, you can check the transponder key.Switch ON ignition with the key which you want to test! Start software, choose "VDO NEW - CAN bus", and press"Transponder Check". Vagtacho USB 4.0 will connects immobiliser.

8.Press "Read ECU Info" button,wait about 10 seconds,the information about this transponder key will be displayed on screen.You can press "Read ECU Info" to testing of transponder key again. This procedure is optional, and is not required when programming the new keys.
step 8
Note:During the whole programming procedure,all parameters must be set "Yes".

Thursday, March 13, 2014


The M35080V6 Programmer was designed for on-board and ISP (in-circuit programming) modes via PC control operation for reading all EEPROM data, incremental area EEPROM writing, EEPROM writing, erasing data to delivery status of M35080V6 SPI EEPROM memory with incremental registers area.

The M35080V6 Programmer can read,program and erase incremental RegistersEEPROM and also can erase time to Delivery State for M35080V6 1-10 minutes;It upports all clock rates 2.5, 5.0 and 6 MHz IC's;In-circuit/On-board EEPROM programming and On-board EEPROM programming for M35080V6 are also supported.The onboard processor ATmega16 allow Firmware to update to new versions.
It has the Self-Check capabilities,and owns 4 adaptors for SO8 device.
In this article,we are focusing on how to install and use the M35080V6 Programmer.Pls follow these steps:
First,install M35080V6 control software. Insert the supplied ETL CD-ROM into a CD drive and navigate to "Install Software" > "Install M35080V6 Prog.", then execute the "Setup.exe" file; this will guide you through the setup process.
(Attention1: M35080V6 software, version 4.0 or later version is required new M35080V6 (rev 4.0) hardware only. Never use version 4.0 to communicate old hardware .)
Second,connect M35080V6 Programmer to the power supply source (12-14 V >=500 mA).
Third,attach M35080V6 Programmer to your computer. Use the 9-pin RS232C cable that is shipped with the M35080V6 Programmer.
Before connecting programmer in ISP mode or inserting target device M35080, make sure that the programmer and a target board are not powered and ISP jumper mounted to ISP position.
(Attention2: M35080V6 can not be ERASED in ISP mode. To erase M35080V6,device must be inserted to the M35080V6 socket. )
(Attention3: Only one mode (on-board or ISP) can be used during operating at a time. )
(Attention4: Don't use at the same time programmer with inserted M35080 or M35080V6 IC in the target socket and ISP mode. When you using ISP mode, make sure that target sockets is empty;When you using target socket make sure that ISP interface not connected and second one socket is empty. )

Fourth,insert M35080/M35080V6 device into a target socket or connect ISP interface cable.

Fifth,now you can start the M35080V6 control software. But remember don't run control software until power supply dose not applied to M35080V6 programmer.

Sixth,turn on the power switch. LED 1 must appear to the Green color telling that power is present and M35080V6 Programmer ready to operate.
Related Download PDF and software:
M35080V6 User Manual.pdf

Wednesday, March 12, 2014


Till now,this is the newest version-- Carprog V5.46.It has airbag repair,vehicle radios,odometers,dashboards,immobilizer,EEprom,MCU and ECU in it.And it can be updated,but pls remember don't update it by yourself or the deveice will be damaged.
Inside of the Carprog V5.46,there is powerful 16-bit MPU and full set of automotive interface drivers.In the basic one,the hardware you will get has 12 input/output pins for EEPROM in-circuit programmer,future possibility's to make on the same hardware Microcontroller programmer,immobiliser transponder key programmer with antenna adapter for 125/134 KHZ,K-line diagnostic,CAN line diagnostic,+5V/+12V output,USB and power supply only from USB.
About the software of the Carprog V5.46,for ECU-OPEL - OPEL login reader from motor hybrid ECU.It works with Bosch ME1.5.5, Siemens SIMTEC71, SIMTEC71.1, Delco Diesel, Delco Multec;
for OPEL CAN - Opel ECU by CAN programmer - it reads/changes mileage in EDC16, MT35E, HSFI 2.2 reads PIN, resets ECU;
for PSG16 - Opel PSG16 diesel pump by OBDII -it reads/changes mileage, reads PIN, resets ECU;
for OPEC28 - Opel Siemens Simtec ECU Tool Advanced.

About the airbag of Carprog V5.46:
S5.1 - VAG (Audi, VW, Skoda, Seat) Airbag Reset Tool
S5.2 - BMW Airbag Reset Tool
S5.3 - Mercedes Benz Airbag Reset Tool
S5.4 - FORD Airbag Reset Tool
S5.5 - GM Airbag Reset Tool by OBDII
S5.6 - CARPROG CR16 Airbag tool - Audi, Mercedes, Ford, Volvo
S5.7 - Renault Airbag reset tool
S5.8 - Peugeot Airbag Reset tool
S5.9 - Citroen Airbag Reset tool
S5.10 - Honda Airbag Reset tool
S5.11 - Audi Airbag reset tool by direct connection to EEPROM or MPU
S5.14 - Ford Airbag Reset tool by direct connection to EEPROM or MPU
S5.16 - Hyundai Airbag Reset tool
S5.17 - KIA Airbag Reset tool
S5.18 - Lexus Airbag Reset tool
S5.19 - Rover Airbag Reset tool
S5.21 - Mazda Airbag Reset tool
S5.22 - Mitsubishi airbag reset tool
S5.23 - Nissan Airbag reset tool
S5.20 - Mercedes Benz Airbag Reset tool by direct connection
S5.25 - Opel Airbag reset tool by direct connection
S5.27 - Saab Airbag reset tool by direct connection
S5.28 - Subaru Airbag reset tool by direct connection
S5.30 - Toyota Airbag reset tool by direct connection
S5.31 - Alfa Romeo Airbag Reset Tool
S5.32 - Fiat Airbag Reset Tool
S5.33 - Porsche Airbag Reset Tool
S5.34 - Suzuki Airbag Reset Tool
S5.35 - Volvo Airbag Reset Tool
S5.36 - Daewoo Airbag Reset Tool
About the Dash of the Carprog V5.46:
S7.1 - VAG CAN programmer
S7.2 - CarProg Dashboard programming
S7.3 - CarProg Dashboard programming package update
S7.4 - Fiat KM correction by OBDII
S7.5 - Mercedes Benz ASSYST explorer
S7.6 - VDO dash decrypt tool - Skoda Roomster, SuperB, VW Polo, Audi A3, A6, Allroad with 93C86 odometer change and PI
S7.7 - Ford odometer change by OBDII (by CAN)
S7.8 - VW 2007+ by OBD - Golf, Passat, Eos, Touran, Tiguan, Octavia with Micronas by diagnostic
S7.10 - VAG VDO dashboards by K-line OBDII diagnostic - VW T5, Passat B5, Skoda SuperB and others
2J74YAUDI - Audi 2J74Y repair software for CarProg
About the Immo of the Carprog V5.46:
S4.1 - Toyota Key Programmer
S4.2 - Lexus key programmer
S4.3 - Daihatsu Key Programmer
S4.4 - CarProg BMW Key programmer
S4.5 - Mercedes Benz Key programmer
S4.6 - RENAULT Megane/Scenic infrared key programmer
S4.7 - Kessy tool - A8, Touareg, Phaeton, Cayenne PIN code reader

About the Processor of the Carprog V5.46:
S2.1 - CARPROG Motorola (Freescale) HC05 MPU programmer
S2.2 - CARPROG Motorola (Freescale) HC11 MPU programmer
S2.3 - CARPROG Motorola (Freescale) HC08 MPU programmer
S2.4 - CARPROG Motorola (Freescale) 912 and 9S12 MPU
About the Programmer of the Carprog V5.46:
ST92 - ST92F120, ST92F150, ST92F250 internal EEPROM programmer

Tuesday, March 11, 2014

FVDI ABRITES Commander For Opel And Vauxhall

FVDI ABRITES Commander for OPEL and VAUXHALL is a professional vehicle diagnostic tool for Opel/Vauxhall vehicles. It's capable to diagnose any unit, which operates under one of the following protocols: Keyword 82, Keyword 2000 and GMLAN.
For all the electronic control units, FVDI ABRITES Commander for OPEL and VAUXHALL can read identification data&error (DTCs),and also can clear off the error (DTCs).Device scan,Data Display/Measured values,Security code&Vehicle identification programming,Injector programming - Diesel engines,Programming of the CAN configuration are all its' functions.
What’s more,it has the program immobilizer functions,which includes the adaptation of Engine Control Module to immobilizer and the adaptation of Immobilizer to the vehicle.The program immobilizer outputs enable/disable Anti Theft Warning system.
1.The function of FVDI ABRITES Commander for OPEL and VAUXHALL----Key Programming
It supports all models programming keys and remote controls by OBDII - ASTRA J, INSIGNIA, Chevrolet CRUZE and all older models.And it can read mechanical key number.
2.Read Security Code
Users can read Security codes of all Opel and Vauxhall vehicles with CAN BUS by OBDII - Astra H, Corsa D, Vectra C, Zafira B, Agila B
3. Read/Write EEPROM
4. It can correct odometer.
5. Engine Flasher--Read/Write flash memory from ECU - Simtec 70, Simtec 71, Delco HDRC, Marelli MJD 602, Motronic
6. It can read radio codes by OBD from Delco CDR500
7. Airbag--Erase crash data by OBD - Airbag SAB6 - Siemens with MCU Motorola HC11
8. Dump Tool
- Airbag TEMIC Astra G, Corsa C (68HC908AZ32) - clear crash data
- SIEMENS (68HC11E9) GM 24416701 DJ - clear crash data
- Read immobilizer II (TMS) security code from dump
- Bosch EDC16 odometer correction
- Magneti Marelli odometer correction
- Astra G, Astra H, Corsa D instrument panel odometer correction
Following are its’ supported Vehicles:
Astra J - 2010+
Insignia - 2008+ (updated supported units)
Agila - 2000-2007 year
Astra F - 1992-2001 year
Astra G - 1998-2009 yer
Astra H - 2004+
Tigra - 1995-2000 year
Tigra B - 2004+
Vectra B - 1996-2001 year
Vectra C/Signum - 2002+
Corsa B - 1993-2001 year
Corsa C - 2001-2008 year
Codsa D - 2007+
Meriva - 2003-2008 year
Zafira - 1999-2005 year
Zafira B - 2005+
Omega B - 1996-2003 year
Frontera - 1997-1998 year
Frontera B - 1999-2004 year
Calibra - 1990-1997 year
Vivaro - 2001+
Movano - 2004+
The software version of FVDI is 6.2,and it only supports English.

Monday, March 10, 2014

2013 NEW Professional Scan AUGOCOM H8 Truck Diagnostic Tool

AUGOCOM H8 Truck Diagnostic tool is newly released with almost the same function as Nexiq. Augocom H8 is suitable with applications that diagnose engines, transmissions, ABS, instrument panels and etc.It can reduce the time of reprogram with direct USB connection.Mixed fleet capabilities with its broad protocol support;It can access to vehicle data for maintenance or management reports fast.Also it can attach to vehicle’s diagnostic connector quickly.It is easy to bring and so flexible to be used with desktop PC or laptop. Besides,Augocom H8 supports Heavy-Duty, Light-and Medium-Duty Trucks.

The packed software and application of Augocom H8 is exactly the same with NEXIQ 125032 USB Link.
- Allison ;
- Bendix ;
- Detroit Diesel DDDL 7.05 ;
- Detroit Diesel DDCT;
- Detroit Diesel Calibration Tool ;
- Eaton Service Ranger 3.2 ;
- International DLB ;
- International ICAP, IPTS, NETS, IPC ;
- International Master Diagnostic ;
- Meritor and Wabco Diagnostics ;
- Cummins Insite 7.5 ;
- Hino 2.0.3. ;
- Caterpillar ;
- Perkins EST 2010B ;
- V Macks 2.6.12 ;
- V Macks Dealer Pro ;
- Volvo VCADS 2.35.10

AUGOCOM H8 Protocol Coverage:
CAN - J1939/CAN125/CAN250/CAN500/CAN1000
2nd CAN - J1939/CAN125/CAN250/CAN500/CAN1000
J1587/J1708 J1850 J2534
ISO 15765 (Diagnostic CAN)
ISO 14230 (KWP2000 over ISO9141) ALDL ATEC 160 (160 baud)

FREE Heavy-Duty Truck Diagnostic Applications:
1.VOLVO TRUCK: FM10, NH565, FH12, FM12, VHD, FH16, FM7, VN, WC, WG, WI, FH565, NH12, FL6, FL7, FL10, FL12, NH525, WX, COMP04, FE, VHD, FH, FM, VM, FM9, F10, F12 , F16, NL10, NL12,VOLVO BUSES: B10B, B10M, B10L, B10R, M10R, B12, B58, B6, B7R, OLYMPIAN, SUPEROLY;
3.MACK TRUCKS: V-MAC I, V-MAC II, V-MAC III, V-MAC IV, Service Diagnostic;
Wheel loader: L110E, L110F, L120E, L120F, L150E, L150F, L180E, L180F, L220E, L220F, L330E, L350F, L60E, L60F, L70E, L70F, L90E, L90F;
Articulated Hauler: A25D, A25E, A30D, A30E, A35D, A35E, A40D, A40E, T450D;
Excavator: EC135B, EC140B, EC140C, EC160B, EC160C, EC180B, EC180C, EC210B, EC210C, EC235C, EC240B, EC240C, EC290B, EC290C, EC330B, EC330C, EC360B, EC360C, EC460B, EC460C, EC700C, EC700B, EC700C, ECR145C, ECR235C, ECR305C, EW140B, EW140C, EW145B, EW145C, EW160B, EW160C, EW180B, EW180C, EW200B, EW210C, FC2121C, FC2421C, FC2924C, FC3329C, PL4611;
Grader: G710B, G720B, G726B, G730B, G740B, G746B, G780B, G930, G940, G946, G960 , G970, G976, G990.
5.Navistar: ALL Diamond Logic Builder (DLB) ServiceMaxx;
6,International: ALL Intune, MD32;
7.Freightliner: ALL ServiceLink:cascadia,century,columbia,Coronado,classic,FLDSD,4900FA, 4900SA,4900EX.
8.HINO: ENGINE:300SERIES, 500 SERIES, CR03_J08E, CR03_J05D, COMMONRAIL(J05E), J05D_US, J08E_US,P11C,VCS, Hibrid, Inverter, Brake(ABS), AT_45043LE;
9.SCANIA VEHICLE, KOMATSU excavator, and MAN vehicle will be updated.

Sunday, March 9, 2014

New Arrival Best Quality Ford VCM II Multi-Language Diagnostic Tool

Ford VCM 2 is the latest diagnostic interface for Ford for using with their IDS(Integrated Diagnostics Software). VCM 2 IDS,along with a dedicated laptop, provide you full dealer diagnostic capabilities for most 16 pin Fords. A fantastic new function of the VCM 2 is its ability to communicate wirelessly with your laptop or computer,without the need of paying for a separate wireless card.This means you can easily work on a car.The VCM 2 will be backwards compatible with most 16 pin Fords, plus it's essential for all new 2013 models.It supports the existing VMM (Vehicle Measurement Module), and new CFR (Customer Flight Recorder). The VCM 2 has shock resistant rubber ends,making it suitable for garage and workshop environments.

The Ford VCM 2 is a direct replacement for the original VCM 1 and offers additional benefits and a lower cost of ownership over the current VCM.Enhancements have been made to the IDS software to integrate the VCM 2 and allow both VCM and VCM 2 to function with existing IDS PCs.

All Ford VCM 2's will operate as a CFR(Customer Flight Recorder) with an optional cable to replace the functionality of the VDR(Vehicle Data Recorder).
Functions of FORD VCM II are what people cares most.
1.Automatic vehicle recognition;
2.Read Clear Diagnostic Trouble Codes (DTCs);
3.Live Data-stream with Recording Playback Functions for Main ECUs;
4.Guided Fault Finding;
5.New Software Re-flash for Existing ECUs;
6.Programming Installation of new ECUs (PCM, ABS, Instrument Cluster, Air Bag, Fuel Pumps, etc.);
7.Program New Keys;
8.Injector Coding;
9.Set, Adjust or Remove Speed Governors;
10.DPF Regeneration;
11.Brake Bleeding;
12.Steering Angle Resets;
13.All Other Dealer Functions.

If you have any other questions, Pls contact us.
Skype: obd2works

Thursday, March 6, 2014

2013 Release 3 Delphi Diagnostic Tools & Equipment DS150E Auto CDP+ With Bluetooth

What we are going to talk about is the 2013 Release 3 Delphi Diagnostic Tools & Equipment DS150E Auto CDP+ With Bluetooth.The version is 2013.03V;and this tool has a bluetooth.
Delphi DS150E owns all functionality of the DS100E and increase more,and transfers it onto a PC platform.
It can diagnose faster,it supports diagnostics on around 54,000 vehicle systems and on more than 4,000 models from over 48 vehicle manufacturers.
It has full system coverage for BMW, VAG, Ford, Peugeot, Citroen, Renault, Vauxhall, Rover, Fiat, Volvo, Mazda, Mercedes, Smart, Nissan, Subaru, Toyota, Hyundai,etc.
Now,we are going to know the languages it supports.They includes English , Cesky, Dansk, Deutsch, Espanol, Francais, Greek, Hollands, Hungarian, Italiano, Norsk, Polish, Romania,Russian, Srpski, Suomen kieli, Svenska, Turkish and so on.
The functions of Delphi DS150:
1.It can read and erase error codes and SLR all system,such as Petrol and Diesel Engine Management,Instrument panel,ABS, Climate control, Immobiliser, Gearbox,SRS and Multifunction(Central Body, Central Locking,Convenience Systems, Chassis, Infotainment, Lights, Navigation, Seats, TPMS etc-Vehicle Specific);
2.It will check,graph and save live data;
3.It can activate component;
4.ECU Coding / Parameter Adjustments / Component Configuration (initialization of new components, particulate filter regeneration, Diesel Injector coding, TPMS etc);
5. It can complete scan all ECU/ECM's on vehicle platform,and it is configurable by system;
6.It has a full vehicle infomation tree,it doesn't need to be connected to a vehicle-customer reporting system, just directly link to Delphi Technical Data,and it will allow vehicle specific check of OBD functionality .
The features of Delphi DS150:
1.Bluetooth Vehicle Communication Interfaces;
2.Now the tool is the newest one Delphi 2013 release 3,Compatibility better than auto,and it keeps updating;
3.It has new design and new Hardware,diagnose faster; 4.More the 4,000 models from over 48 Vehicle Manufacturer which ncludes 85% European models; 5.Exceptional value for money – operates from a garages existing PC;
Pay attention to following points when you install 2013 Delphi DS150 software:
First,make sure your PC hadn't install any other version autocom or cardiag M8 software.Don't have any other software which is not conpatibility with it;
Second,your computer system should be compatible with this software.
Over 95% users can install this software successfully. Some users will meet error prompt when install it. This 2013 software is sensitive to computer,that's why some users say they can install the old version successfully, but cannot install this 2013 version on the same computer.
If the software or your system is not compatible with it, it will meet the following problem:1) Software cannot recognize the hardware, means VCI NO Found problem;2) You can't update the hardware;3) Hardware test result is OK, but you can't use it to test your car.
When you meet these problems,I mean if there is some other software can't compatible with this software,pls reinstall the system and format the HDD(because if there still has the file in your PC which influences the installation of this software,problems can't be solved),then reinstall the software again.

Wednesday, March 5, 2014

CK-100 Auto Key Programmer V45.02 SBB

Here is the newest version of auto key programmer--V45.02.It is the updated version of SBB V33.02,and of course it increases much more functions.Now CK-100 Auto Key Programmer V45.02 SBB is more powerful and efficiency than the old version,also,its' quality is much better.
This version supports English,Italiano,Deutsch,Francais,Espaniol,Portuguese and Turkish.
Let's review the functions of the V33 SBB.
SBB Key Programmer,as its' name said,of course it can program new keys,and also program new remote controls.Besides,it can read keys from immobilizer's memory,and won't deactivate keys in the car owner's possession.It operates by means of a menu guided programming.The highlight is that the software with full database which includes all the most important vehicle makes.
In this article, I wanna show you this product by comparing with the old SBB via using images.
Related Download File: